HIGH VOLTAGE DC POWER SUPPLY
160kV to 220kV, 100W to 1kW
HIGH VOLTAGE DC POWER SUPPLY
160kV to 220kV, 100W to 1kW
This series of power supplies can generate output that ranges from 160kV to 220kV, 100W to 1kW and the high voltage sections are housed in oil-filled HT tanks and the control sections in compact 19” racks to give a highly regulated output.
Download Datasheet
TECHNICAL SPECIFICATIONS
| PARAMETER | SPECIFICATION | ||||||
|---|---|---|---|---|---|---|---|
| Input Voltage | 230V ±10% A C, 50Hz, single phase | ||||||
| Output Voltage Range* | 160kV to 220kV DC | ||||||
| Output Power Range* | 100W to 1kW | ||||||
| Polarity* | Positive / Negative | ||||||
|
|
||||||
|
|
||||||
| Stability | < 0.05/hour after 1 hour warm up | ||||||
| Temperature Coefficient | < 0.05% / ℃ | ||||||
| Regulating Mode | Constant current – Constant voltage | ||||||
| Cooling | Oil cooling | ||||||
| Voltage & Current Control # | Local: By 10-turn potentiometers on the front panel Remote: 0 to 10V DC signals for voltage & current control; OR Control through computer interface |
||||||
| Protections | Protections Against over voltage, over load, short circuit and arc | ||||||
| Remote Controls & Signals through Pluggable Connector / D-Connector (External RS232 Microcontroller Module) # |
10V DC reference 10V DC HV enable signal 0 to 10V DC signal for voltage & current control 0 to 10V DC signal for voltage & current monitoring |
||||||
| Front Panel | Power ON/OFF switch with indication HV ON/OFF switch with indication 3½ digit current and voltage meters 10-turn potentiometers for current and voltage control Constant current – constant voltage mode indication |
||||||
| Back Panel | Socket for mains input with 250V, 10A 3 conductor power cord of 1.5 meters Fuse holder with fuse Stud for grounding the unit Remote interface connector # |
||||||
| Topology | High frequency resonant / PWM-controlled switch mode | ||||||
| Switching Device | IGBT | ||||||
| Cabinet | 19” rack, powder coated for control section HT tank for high voltage section |
*To be specified by the customer
# For remote operation RS232 available at an extra cost
Remote Interface Connector Configuration
| Pins | 14 Pin Pluggable Connector (Analog Interface) | 25 Pin D Connector (Digital Interface) |
|---|---|---|
| 1 | Earth | Earth |
| 2 | Common | Common |
| 3 | Interlock | HV Enable |
| 4 | HV Enable | Voltage Control Remote |
| 5 | Reference | Current Control Remote |
| 6 | Common | Over Voltage Control Remote* |
| 7 | Voltage Control Remote | Over Current Control Remote* |
| 8 | Voltage Control Local | Common |
| 9 | Common | Voltage Monitor |
| 10 | Current Control Remote | Current Monitor |
| 11 | Current Control Local | Reserved Monitor* |
| 12 | Common | Reserved Monitor* |
| 13 | Voltage Monitor | Common |
| 14 | Current Monitor | Mode Status |
| 15 | Interlock Status | |
| 16 | HV ON Status | |
| 17 | Common | |
| 18 | PS Fault Status* | |
| 19 | Over Voltage Status* | |
| 20 | Over Current Status* | |
| 21 | Over Temperature Status* | |
| 22 | Open Circuit Status* | |
| 23 | Phase Failure Status* | |
| 24 | Reserved Status* | |
| 25 | Common |
*Optional. To be specified by the user only as per application’s requirement.
Ordering Code HV 040 K 600 W N C U D 5 T
| Ordering Code |
|
|
|
||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Section | Description | Options | Options Description | ||||||||||||||||||||||
| 1 | Output Voltage | XXX | Value of output voltage | ||||||||||||||||||||||
| 2 | Output Power | YY | Value of output power | ||||||||||||||||||||||
| 3 | Polarity |
|
|
||||||||||||||||||||||
| 4 | Short Circuit |
|
|
||||||||||||||||||||||
| 5 | Regulation Mode |
|
|
||||||||||||||||||||||
| 6 | Control Mode |
|
|